Be sure that your system is clean and your tape tabs are free of any oils or conditioning agents. Wiping the tape tab with alcohol before starting will help eliminate any residual oil. Find a contour that best suits your systems design. You may also find it easier to use tape that comes in a roll and cutting the pieces to fit your system exactly. Remove the liner and place the tape to the underside of the base and to the edge of the tape tab. Press firmly to the tab. You can also assure good adhesion by rubbing the tape backing with the back of a brush, flat part of a comb or plastic card (like a credit card). When the tape is firmly attached you will find it easy to peel away the backing of your tape and apply.

Applying your system to your head

Before applying you may want to prep your scalp for the attachment as well. We have a great Skin Care product that removes any residual oils, calms the skin, closes the pours preparing your scalp for the attachment and the days wear.

Starting in the front, place your system on your head, in the proper location, and gently roll the system back adjusting it into place as you go. Once the system is completely down and sitting correctly on your head, press the tape firmly into place. You’re now ready to do your final styling and you’re out the door.

Begin by brushing your wig to remove any tangles. When brushing always start at the tips of the hair and work your way up to the front. This way you aren’t brushing any tangles through other tangles and avoid hair breakage. Once you have your wig thoroughly brushed hold it by the front edge and wet under a low pressure stream of lukewarm water. Once your wig is completely wet put a small amount of shampoo into the palm of your hand and emulsify with water. Starting at the tips of the hair begin lathering by pressing the shampoo into the hair. Avoid any rubbing or scrubbing while shampooing. Work your way up to the front of your wig and press the shampoo into the base of the wig. Continue to massage the shampoo through the wig. When you feel your wig is clean hold by the front again and rinse thoroughly at least 3 minutes to assure all the shampoo has been rinsed from the hair and especially the base material. You may want to repeat the shampooing process one more time to assure all residues and buildup is removed from the base of your wig. If you find areas that are stubborn use a “SOFT” bristle tooth brush in those areas to loosen the build up.

When conditioning with a rinse out conditioner, apply the conditioner in the same manner as the shampoo avoiding the base of your wig. Conditioner should only be applied and massaged into the hair and the ends are the most important area to concentrate on. Allow the conditioner to stay on the hair for a minimum of 3 minutes and rinse thoroughly for a minimum of 3 minutes. It is essential that you remove as much conditioner from the base as possible so try not to get any conditioner on the base at all.

Once your wig is cleaned and conditioned place it on a clean absorbent towel and gently roll the wig into the towel pressing to remove any excess moisture. Remove from the towel, hold by the front and gently shake the wig to fluff the hair. Using a broad brush or wide tooth comb starting at the tips of the hair go through your wig to smooth and remove any tangles there may be. Once you’ve combed through the hair shake the wig again to fluff the hair.

It’s best to place your wet wig on an open wig stand as opposed to a Styrofoam or canvas wig block. This allows your wig and base to dry completely. If using a hair dryer, we recommend an Ionic dryer and dry the wig holding the front and working the dryer through the hair as well as the base. You shouldn’t dry completely with the dryer. Leave the wig slightly damp and continue to air dry.

If you use a tape tab for tape or adhesive be sure to wipe these areas with alcohol before applying tape to assure all conditioner residue is removed from the tape tab areas.

You want to start your off the head cleaning with removing any tape, adhesive and residue from the tape tabs, base, lace front and hair.

Always use Adhesive remover when removing tape from the tape tab area. Even if you have a durable heavier tape tab, it will allow the tape to be easily removed eliminating any chance of damage to your system this is particularly important with all skin systems. We also recommend soaking your system in our Yellow Cleaner/Conditioner. This is a safe and effective all natural product that effectively breaks down the adhesives and loosens any residue in the mesh, lace or hair. To get that stubborn accumulation from your system use a “SOFT” bristle tooth brush and gently brush the residue away from the base and hair.

Once the tape, adhesive and residue have been removed, add a capful of shampoo to a basin or plastic container. Add lukewarm water and emulsify the shampoo in the water. Place your system base side up in the basin and gently swish in the soapy water. You may let your system sit for several minutes if you wish. (We suggest you repeat this procedure 2 to 3 times to assure all the cleaner/conditioner or solvent has been removed from the system) Rinse your system under lukewarm running water for at least 3 minutes and check to be sure all adhesive and solvent residues have been removed. Repeat the washing of your system if necessary.

If you choose to use rinse out conditioner, add a capful to your clean basin. Fill with water and emulsify the conditioner. Allow your system to soak for a minimum of 3 minutes and rinse thoroughly.

(When rinsing, hold your system by the front and allow a low pressure stream of water flow from the bottom of the base through the hair.)

Place your clean system on a clean absorbent towel and gently roll the towel with the system inside to remove excess water. Holding the system by the front of the base gently wave in the air to fluff the hair. You can then apply leave in conditioner and any styling product you choose. Gently brush into your desired style and let air dry if possible.

Before re-applying your tape or adhesive you may want to wipe the tape tab with a small amount of alcohol to remove any conditioner residue that may be on your tabs. This will allow for your attachment to work at its optimum.